Rice and Wheat Rice Milling Machine can process rice into the rice at one time and complete the separation of rice, alfalfa, and broken rice. The crushed part can be used to crush rice, Corn, sorghum, beans, potatoes, stems and beating. However, the water content and impurities of the processed material will directly affect the quality of the rice and the machine and load. For other purposes, it will be contrary to the intended use of the machine. The following The motor drives Rice and Wheat Rice Milling Machine wholesale manufacturers to everyone to introduce the rice and wheat rice mill instructions.
1. Wiring requirements: This machine cannot be shared with the original lighting circuit. It must use copper wire or aluminum of 4 square millimeters or more directly from the main power switch.
2. Operation: Before starting the machine, carefully check whether the fasteners in all parts of the machine are loose, and open the cover to check whether the gap of the rice roller is correct.
The gap between the general rice knife and the tip of the rice roller is about 3 mm at the beginning of the rib and about 2.5 mm at the end of the rib.
3. Close the switch and run idle for 1-3 minutes. If the operation is normal, it can be processed. When opening the feed insert, it should be pulled open.
Make the machine gradually load, otherwise suddenly increase, it may make the machine block the car.
4. Stop midway, should first close the feed port, let the mill in the rice mill room finish grinding and then stop.
The motor drives Rice and Wheat Rice Milling Machine use/application areas:
A. The grain that needs to be processed should be screened first to remove the stone, metal and other debris from the grain.
B. Add 5-6% of water to the food and stir for 10 minutes before processing.
C. After the material is added to the hopper, the standby control unit is gradually opened and the feed control panel is slowly opened.
D. In order to fully peel and effectively clean, generally need continuous peeling.
E. Keep the air duct of the whole machine unblocked, and the exhaust air outlet should have enough air exhaust volume.
F. The inlet and outlet control panels have flow, maintain the pressure of the peeling chamber, which directly affects the machine's output, the removal rate and power consumption, the feed control panel is opened, the amount of material entering the peeling chamber, the force increases, Peeling effect, but power consumption and tax break rate also correspond. If the inlet opening is too large and the outlet opening is too small, the machine will be blocked. Conversely, if the inlet is too large and the outlet is too large, the productivity peeling effect will decrease. In the operation, the flow rate is appropriately controlled by the feed port, the discharge control panel is adjusted, and the pressure inside the machine is matched to achieve satisfactory results.
1. Wiring requirements: This machine cannot be shared with the original lighting circuit. It must use copper wire or aluminum of 4 square millimeters or more directly from the main power switch.
2. Operation: Before starting the machine, carefully check whether the fasteners in all parts of the machine are loose, and open the cover to check whether the gap of the rice roller is correct.
The gap between the general rice knife and the tip of the rice roller is about 3 mm at the beginning of the rib and about 2.5 mm at the end of the rib.
3. Close the switch and run idle for 1-3 minutes. If the operation is normal, it can be processed. When opening the feed insert, it should be pulled open.
Make the machine gradually load, otherwise suddenly increase, it may make the machine block the car.
4. Stop midway, should first close the feed port, let the mill in the rice mill room finish grinding and then stop.
The motor drives Rice and Wheat Rice Milling Machine use/application areas:
A. The grain that needs to be processed should be screened first to remove the stone, metal and other debris from the grain.
B. Add 5-6% of water to the food and stir for 10 minutes before processing.
C. After the material is added to the hopper, the standby control unit is gradually opened and the feed control panel is slowly opened.
D. In order to fully peel and effectively clean, generally need continuous peeling.
E. Keep the air duct of the whole machine unblocked, and the exhaust air outlet should have enough air exhaust volume.
F. The inlet and outlet control panels have flow, maintain the pressure of the peeling chamber, which directly affects the machine's output, the removal rate and power consumption, the feed control panel is opened, the amount of material entering the peeling chamber, the force increases, Peeling effect, but power consumption and tax break rate also correspond. If the inlet opening is too large and the outlet opening is too small, the machine will be blocked. Conversely, if the inlet is too large and the outlet is too large, the productivity peeling effect will decrease. In the operation, the flow rate is appropriately controlled by the feed port, the discharge control panel is adjusted, and the pressure inside the machine is matched to achieve satisfactory results.
